Can't use INSTEON because you don't have neutral wires in your switch boxes? You can now, with our new INSTEON 2-wire On/Off Switch Kit. Remotely control your lights or appliances, even if you don't have those once-needed neutral wires in your switch boxes. Now you can enjoy the speed and reliability of INSTEON where never-before possible.

Don't have a neutral somewhere you'd like dimming control? An INSTEON 2-wire Dimmer Kit is also available.

How it Works
The INSTEON 2-wire On/Off Switch Kit comes with two main pieces: a companion switch that installs in the switch box and a fixture module that installs in your light (or appliance) fixture. With these two devices you'll now be able to convert one of your two wires in your switch box to a neutral, enabling reliable control of your light or appliance. The companion switch and fixture module are "paired" at the factory so both devices will act as one. This means that once they're installed, you won't have to go back into the fixture, either for control OR for linking to other INSTEON-compatible devices. Simply put, the companion switch's SET button acts as a remote SET button for the fixture module, giving you added convenience and flexibility.

Scene Lighting
Scenes allow you to control multiple lights, rooms or even the whole home with a single command. Because the 2-wire kit can be a member of more than 400 scenes (i.e. "Movie Time," "Party," "Romance," etc.), you'll be able to launch various lighting scenarios with a single button press. These are elegant features usually found only in systems costing tens of thousands of dollars and requiring extensive rewiring of your home.

X10 Compatible
The INSTEON 2-wire Kit is fully INSTEON compatible and X10 ready. Homeowners with existing X10 networks can easily migrate to an INSTEON network without having to discard all their existing X10 devices. X10 ready means that it can respond to X10 commands from an X10 controller and it can send X10 commands to X10 devices. Please note that INSTEON devices repeat INSTEON signals but not X10.

Non-Volatile Memory
All 2-wire kit settings are stored in non-volatile memory and are not lost during power failures. Additionally, in the event of a power loss, the 2-wire On/Off Kit will return to its last on/off state when power is restored.

Certifications and Warranty
All SmartLabs Design products are safety approved. The factory for SmartLabs Design products is ISO9001 certified. Because of this passion for quality, Smarthome stands behind the entire line of products with a full 2-year warranty.

Fixture Module Specifications
General
Brand:	Smarthome
Manufacturer:	SmartLabs Design
Manufacturer Product No.:	2474S, INSTEON 2-Wire On/Off Switch Kit
UPC:	689076408844
Patent No.:	U.S. Patent No. 7,345,998, International patents pending
Multi-Way Circuit Support:	Yes, as a receiver only that controls a load
Warranty:	2 years, limited
Operation
Operation Modes	INSTEON only, X10 only, INSTEON and X10 Combo Mode
Combo Mode Message Order	INSTEON, X10, INSTEON cleanup
LED Indicator:	Off when load is on and vice versa
Setup Memory	Non-volatile EEPROM
INSTEON Features
INSTEON Addresses	1 hard-coded out of 16,777,216 possible
INSTEON Links	417
INSTEON Powerline Frequency	131.65 KHz
INSTEON Minimum Transmit Level	3.2 Vpp into 5 Ohms
INSTEON Minimum Receive Level	10 mV
INSTEON Messages Repeated	Yes
Mechanical
Wire Nuts	3 included
Mounting	Mounts in single-ganged junction box or light fixture such as a recessed can light.
Operating Conditions	Indoors, 0 to 104°F, up to 85% relative humidity
Dimensions	3.75" H x 1.8" W x 1.2" D (2.75" H without screw tabs)
Weight	3.6 oz
Electrical
Supply Voltage	120 Volts AC +/- 10%, 60 Hertz, single phase
Surge Protection	MOV rated for 150 Volts
Power Wire Leads	6", 16 AWG, stranded,600V, 105°C insulation, ends stripped and tinned, LINE (black), LOAD (red), NEUTRAL (white)
Ground Lead	6", 18 AWG, stranded, bare copper
Load Types	Wired-in incandescent lighting devices, inductive and resistive loads
Maximum Load	13 Amps; 400 Watts (for incandescent loads)
Minimum Load	No minimum load required
Certification	Safety tested for use in USA and Canada (ETL)
X10 Features
X10 Primary Address	1 optional (comes unassigned)
X10 Scene Addresses	255 possible
X10 Status Response	Supported
X10 Powerline Frequency	120 KHz
X10 Minimum Transmit Level	3.2 Vpp into 5 Ohms
X10 Minimum Receive Level	10 mVpp nominal
X10 Messages Repeated	No

Companion Switch Specifications
Operation
Warranty:	2 years, limited
LED Indicator	One Amber LED
Operation Modes	INSTEON only, X10 only, INSTEON and X10 Combo Mode
Combo Mode Message Order	INSTEON, X10, INSTEON cleanup
Setup Memory	Non-volatile EEPROM
INSTEON Features
INSTEON Addresses	1 hard-coded out of 16,777,216 possible
INSTEON Links	30
INSTEON Powerline Frequency	131.65 KHz
INSTEON Minimum Transmit Level	3.2 Vpp into 5 Ohms
INSTEON Minimum Receive Level	10 mV
INSTEON Messages Repeated	Yes
Mechanical
Paddle Type	True rocker action
Color	White installed, Optional Ivory, Almond, Black, Brown, or Gray
Wire Nuts	3 included
Mounting	Mounts in single or multiple-ganged junction box.
Operating Conditions	Indoors, 40 to 104°F, up to 85% relative humidity
Dimensions	4.1" H x 1.8" W x 1.2" D
Weight	3.6 oz
Electrical
Supply Voltage	120 Volts AC +/- 10%, 60 Hertz, single phase
Surge Protection	MOV rated for 150 Volts
Power Wire Leads	6", 16 AWG, stranded, 600V, 105°C insulation, ends stripped and tinned, LINE (black), NEUTRAL (white)
Ground Lead	6", 18 AWG, stranded, bare copper
Certification	Safety tested for use in USA and Canada (ETL #3017581)
X10 Features
X10 Primary Address	1 optional (comes unassigned)
X10 Scene Addresses	N/A
X10 Status Response	Supported
X10 Resume Dim	Supported (by setting Local On-Level to zero)
X10 Powerline Frequency	120 KHz
X10 Minimum Transmit Level	3.2 Vpp into 5 Ohms
X10 Minimum Receive Level	20mV into 5 Ohms
X10 Messages Repeated	No

* Allows you to remotely control lights or appliances where a neutral wire is not present in the switch box

* Controls any load type, such as fluorescent lights, fans, and motors!

* Convenient: Once installed, companion switch and fixture module operate as one device from the switch

* Uses existing wires to provide a neutral to your companion switch for added reliability

* Award-winning INSTEON technology provides superior performance and reliability