Control Any INSTEON-Compatible Device with the World’s First INSTEON Motion Sensor 

Essential Info
Turn on your INSTEON-controlled lights or appliances when you enter the room and turn them off after you've left. Truly automating your lighting, this motion sensor is perfect for areas of your home such as the laundry room, closets and the garage where lights commonly get left on. Use this motion sensor for indoor or outdoor applications, and link it to a wall switch, plug-in lamps or appliances. You can even have the motion sensor trigger your thermostat to a favorite comfort level when you enter your home or any room in your house.

Additional features include an adjustable 'Off' countdown timer delay, night-only mode with adjustable light sensitivity settings, adjustable motion sensitivity, wireless range of up to 150', 40-foot field of vision and a pivoting mounting bracket. INSTEON Wireless Motion sensor is a must-have for any INSTEON home automation network as an addition that will make your life more convenient, fun and energy-efficient. A 9 Volt battery is required and included.

Required Accessory
Since the motion sensor only transmits RF signals, your home must have at least one Access Point or dual-band INSTEON device to interpret the command for controlling powerline only devices.


How it works
When the sensor detects motion it sends a wireless RF signal to a plug-in Access Point (sold separately) which in turn relay the signal over your existing power wires to turn on things like lamps or wall switches. After a selectable time of no motion, the sensor turns those same lights (or appliances) off.

UPDATE: with the release of the new LampLinc Dual-Band, this motion sensor can control a lamp without the need of an Access Point.

Optional Power Supply
A Plug-In 9-Volt Power Supply (Battery Eliminator) can be used in place of a 9 Volt battery, eliminating the cost and trouble of regularly replacing the battery. To install, just notch a small hole using a file or shear on the Motion Sensor battery door (for the power supply wire) and plug it in.

Note About PIR Sensors
As with all PIR (Passive Infrared) motion sensors, there are certain factors which can cause detection range / reliability to vary. Because PIR sensors rely on changes in heat to detect motion, be aware of the following factors that can effect PIR reliability when choosing a location to mount your INSTEON Motion Sensor:

Rapid environmental changes
Direct sunlight
Direct wind from a heater or A/C
Fireplaces

Also, please note that certain types of treated glass may or may not act as an infrared 'wall' through which a motion sensor can detect. If you want to detect motion through glass, we recommend you test it in your particular application. Note: Any accumulation of ice, snow or dirt on the Fresnel lens may also interfere with the motion sensor’s ability to detect motion.

Never Leave Another Light On Again
INSTEON Wireless Motion Sensor is a great energy-saver: Your lights will turn on when you enter and automatically turn off after you leave, so you’ll never have to worry about leaving your lights on. Also, INSTEON Wireless Motion Sensor has a built-in photocell, so it can be disabled during the day. If daylight is enough to light your house during the day, Motion Sensor can leave the lights off, even when motion is detected. Using Motion Sensor to limit the amount of time lights are on, is a great first step towards saving energy and protecting the environment.

Unlock More Motion Sensor Options with HouseLinc 2
Get HouseLinc 2 and you'll be able to make adjustments to the INSTEON Wireless Motion Sensor without having to touch it again. These adjustments include:
Delay
Change the Off duration to anywhere between 30 seconds up to 2 hours.
Indicator Intensity
Controls the LED indicator brightness. This is good when you have the motion sensor in a bedroom and don't want the distraction of the red LED when it's being activated.
Ambient Light
Adjust the sensitivity of the motion sensors photocell (light sensor). This allows you to set the amount of light the motion sensor is required to see before transmitting a comman
Dusk / Dawn Sensor
Save energy by ensuring lights are off at dawn or turn your porch lights on at dusk with INSTEON Motion Sensor's dusk / dawn feature. When used with supported INSTEON software or an INSTEON automation controller, Motion Sensor can also be used as a dusk/dawn sensor. After it has been bright for 3 and a half minutes, Motion Sensor will send an Off command for its 'Group 2', which can be used to turn off lights and appliances or trigger a software event. Conversely, it will send an On command after it has been dark for 3 and a half minutes.

Low Battery Warning
Get notified when it's time to change the battery. INSTEON Motion Sensor has 2 methods of indicating the battery life is low:

-LED double-flashes after motion is detected (even if LED is disabled)
-On command is sent to 'Group 3', which can be utilized with INSTEON software or an INSTEON automation controller

For extended battery life, consider purchasing a 9V Lithium battery which can extend battery life by 4 times.

If you have a need for the motion sensor to activate many links, using HouseLinc or another software that supports this product can extend battery life.

Paintable
Motion Sensor has been manufactured with a surface that can be painted to blend in with your home décor. This gives you the ability to decide exactly what color will give your motion sensor installation that professional finished look. Please note, it is recommended that you protect the Fresnel lens during the painting process. Any excess paint or residue may cause motion sensor to operate improperly.

General
Brand:	Skylink
Manufacturer:	Skylink
Manufacturer Product No.:	2420m
Color:	White
Range:	150' (line of sight)
Frequency:	915MHz ISM Band
Warranty:	1 year
UPC:	718122388714
Patent No.:	U.S. Patent No. 7,345,998, International patents pending
Operation
Sensitivity Modes:	High (default) or Normal
Status LED:	1, Red behind PIR lens, normally off, blinks during setup
Setup Memory:	Non-volatile EEPROM
Motion Detection Range:	up to 110° arc, 40 feet
Motion Detector Sense Input Type:	PIR and photocell
Operating Temperature Range:	Indoor / Outdoor, 0 to 120°F. Note: PIR reliability may vary with temperature
Operating Humidity Range:	10% - 90%
INSTEON Features
INSTEON Addresses:	1 hard-coded out of 16,777,216 possible
INSTEON RF:	Yes
INSTEON Links:	30
INSTEON Device Category:	0x10
INSTEON Device Subcategory:	0x01
INSTEON Product Key (IPK):	0x00004A
Mechanical
Dimensions:	2 1/4" x 3 1/4" x 1 7/8"
Weight:	4 oz
Electrical
Input Power Voltage Type:	9VDC
Power Supply:	9VDC battery (included)
Battery Life:	6 months min.
Certification:	FCC (pending)

Manuals/Software

What's Included

Motion Sensor
Mounting Bracket
2 Mounting Screws
9V Battery
Quick-Start Guide

* Automatically turns INSTEON devices off after motion stops (adjustable anywhere between 30 seconds and 2 hours)

* Optional night-only mode allows you to keep your lights off during the day

* Adjustable high/low motion sensitivity provides flexible placement

* Adjustable day/night threshold

* Remotely control your INSTEON devices Excellent range - up to 150' from nearest Access Point or RF INSTEON device

* Award-winning INSTEON technology provides superior performance and reliability